新闻动态
铝包木门窗单独从一个样品窗上
铝包木门窗单独从一个样品窗上即可看到结构与工艺的不同，如果从大面积工程的质量上去衡量，就会完全分辨得清哪种窗的结构更合理，质量更过关，至于国内
许多厂家不敢做零售市场，并不是因为零售市场小，而是由于质量不过关，但是，在零售市场中，绝大多数的质量也是非常不达标的，所以想选择一扇好的门窗，更
多是需要多看多参考，窗的质量好与坏并不在于价格与品牌。
Aluminum clad wood doors and windows can be separate from a sample
window to see structure and process, if the quality of large area
project to measure up, will be completely resolved clearly what kind of
window structure more reasonable, quality clearance, as many domestic
manufacturers do not dare retail market, not because the retail market
is small, but because of quality is, however, in the retail market, the
vast majority of quality is also very substandard, so I want to choose a
good window, more is needed to see the reference window, quality good
and bad is not the price and brand.
7.漆料的选择
Selection of 7. lacquer
铝包木门窗在油漆选择必须为门窗专用漆,目前市场情况需使用水性漆,要具有良好的质感与密闭性,还要抗紫外线耐黄变与退色,漆膜厚度在0.15mm-0.2mm之间,也就是正常喷漆术语中的1-2°,且要喷涂均匀没有色差无尘粒,木材接缝处色差控制在0.2°以内为合理.
Aluminum clad wood doors and windows in the paint must be for paint
doors and windows, the current market conditions require the use of
water-based paint, good texture and tightness, but also anti ultraviolet
yellowing and discoloration, the film thickness is between
0.15mm-0.2mm, is also the normal painting in terms of 1-2 degrees, and
no uniform color spraying dust particles wood, joint color at 0.2
degrees or less reasonable.
8.木料型材的辨别
8. wood profile identification
木材选择,一般铝包木门窗(铝木复合门窗)木材选择均应使用集成材,集成材指接长度在40cm-80cm之间,厚度必须在15mm以上才能保证木材材性的强度，要求无节及较小色差并且明齿指接,指接处缝隙不得超过0.1mm;纯木窗木材需要选择三层指接板拼接成的木方,特殊需要时可以选用四拼,如使用针叶类木材，须木材原材经径切成板后再指接,最后需要对应拼接成方木，才可以良好的抵消木材之间的互应力,达到不变型的效果。
Wood, aluminum wood doors and windows (aluminum wood composite
doors and windows) wood selection shall use timber, timber finger length
between 40cm-80cm, in order to ensure the thickness must be above 15mm
of wood strength, no color and Ming Festival and small tooth finger
finger joint, the gap should not exceed 0.1mm; pure wood windows need to
choose three layer wood finger board spliced into the wood, special
needs can be chosen four pieces, such as the use of conifer wood, the
wood raw material by size shall be cut into the plate and then finger,
finally we need the corresponding spliced wood, can cross stress between
offset wood good, achieve the same type of effect